Powered by GeoSense-PI™ technology, the GPX 6000 is the fastest, lightest and simplest way to find all types of gold in one machine.
GeoSense-PI ™ 기술은 땅에 묻혀있는 금 신호를 빠르고 정확하게 분석하므로 모든 금 조각을 선명하게들을 수 있습니다.
이 하나의 검출기로 작은 조각에서 큰 덩어리까지 그리고 그 사이의 모든 것을 정확하게 찾을 수 있습니다.
자동 기능과 사용하기 쉬운 인터페이스를 통해 GPX 6000을 켜는 순간부터 금을 찾는 데 전문가가 될 것입니다. 자동 그라운드 발란스는 감지기를 지면 위로 휘두를 때 변화하는 토양 조건에 지속적으로 적응하기 때문에, 설정을 조정할 필요가 없습니다. 금을 찾는 것이 그 어느 때보다 쉬워졌습니다.
GPX 6000 ™ Learn 모듈 로 Easy Expert가 되십시오. 이 짧은 비디오는 GPX 6000 금 검출기를 작동하는 방법을 배우는 데 도움이됩니다.
무게가 2.1kg (4.6lb)에 불과하며 가벼운 탄소 섬유 샤프트, 유선형 컨트롤 박스 및 시그니처 U-Flex ™ 팔걸이가 특징이므로 더 오래 감지하고 편안하게 할 수 있습니다.
호주 아웃백, 아프리카 및 중동의 혹독한 환경에서 테스트 된 GPX 6000은 극심한 더위와 폭우를 견딜 수 있습니다. Minelab의 글로벌 지원을 통해 3 년 보증이 포함됩니다.
코일 옵션에는 좁은 공간과 작은 금 조각을 찾아 내기위한 다용도 11 "Monoloop 코일, 염분이 많은 환경에서도 금을 정확하게 감지하는 14"Double-D 코일, 지역을 더 빨리 검색하고 큰 덩어리를 찾을 수있는 17 "Monoloop 코일이 있습니다. 코일은 1m (3.3 ')까지 방수됩니다.
크고 선명한 외부 스피커를 사용하든 제공된 무선 Bluetooth® 헤드폰을 사용하든 금색의 사운드를 놓치지 않을 것입니다.
GeoSense-PI™ technology analyses and responds to ground signals with great clarity and precision, so you can detect in difficult environments once thought undetectable.
It rapidly suppresses unwanted signals via three overlapping feedback systems for superfast detection of even the tiniest gold pieces.
Powered by GeoSense™ technology, the GPX 6000® is in tune with you and the earth.
26th Aug 2022
Minelab has identified infrequent cases where users hear audio feedback when using the internal speaker. Please refer to the product notice on our website by clicking on the link below.
https://www.minelab.com/support/product-notices?article=482551
Minelab have produced a hardware update that removes this effect. This update is present in all newly manufactured GPX6000s.
In the event you have a production standard without this update and have experienced audio feedback when using the speaker please follow the procedure below in Australia to arrange for this update to be completed on your detector.
Please note for maximum performance headphones should be used. Headphone performance is unaffected with this update.
Australia
1. Contact Minelab head office via phone or email.
service@minelab.com.au
(08) 8238 0888
You will need the following information ready to give to Minelab staff:
- Full name
- Contact phone number
- Return postal address
- Detector serial number (located on the bottom of the control box)
2. Minelab staff will then determine if your detector already has the hardware update.
3. To have your detector updated you will need to send your detector control box to the following address.
Minelab Service
2 Second Avenue
Mawson Lakes
South Australia
5095
USA
1. Contact Detector Center via phone or email (www.detectorrepair.com).
newrepair@detectorrepair.com
(814) 283 4270
You will need the following information ready:
- Full name
- Contact phone number
- Return postal address
- Detector serial number (located on the bottom of the control box)
2. We will then determine if your detector already has the hardware update.
3. To have your detector updated you will need to send your detector control box to the following address.
Detector Center
188 Oak Shade Road
Alum Bank, PA 15521
Removing the GPX 6000 Control Box
*Please note if you are not comfortable removing the control box from the shaft assembly simply send the complete assembly*
To remove the control box from the upper shaft and display assembly please follow the below procedure.
1. Disconnect the coil and remove the lower shafts from the upper shaft.
2. Remove the screw holding the speaker cover in place on the rear of the control box with a medium sized Phillips head screwdriver.
3. Lift the lower part of the speaker cover away from the control box and then lift the speaker cover out of the 2 upper tabs as shown below.
4. Unplug the control box connector and remove the two large Phillips head screws at the top of the control box.
5. Gently slide the control box away from the shaft assembly.
6. Replace the speaker cover on the rear of the control box and tighten the screw. Package and send to Minelab.